Tiller Stake Settings

Husqvarna dual-rotating rear-tine tiller

Which stake goes where, for the job in front of you.

Pick the tine direction first. Forward tines: silver drag stake DOWN. Reverse tines: silver drag stake UP. Then set depth.

Know the two stakes

Silver bent bar = drag stakeDrawn as the clear outline on the decal. Two positions: #1 down (forward tines), #2 up (reverse tines). It drags behind the tines and holds the tiller back.
Black bar with holes = depth stakeSolid black on the decal. Rides on the ground. The lower it sticks out, the shallower the tines dig. Holes run Transport, then Cultivate, then Till.
Black depth stake with a row of holes beside the bent silver drag stake
Black depth stake, left. Silver drag stake, right.
Warning decal showing drag stake and depth stake adjustment
The decal on the tine hood.

Quick table

JobTinesSilver dragBlack depth
Finish a seedbed, 2 to 3 inForward#1 downRaised, bottom holes
Weed between rows, 1 to 2 inForward#1 downRaised, bottom holes
Break sod or new groundReverse#2 upCultivate first, then Till
Turn in compost or leavesReverse#2 upUpper Till holes
Stony or rooty groundForward#1 downRaised; go slow
Move it across a lawn or driveOffEitherTransport hole

Example situations

1. Finish a tilled lawn bed before seeding

Tines
Forward
Silver drag
Down to #1, pinned
Black depth
Slid up, pinned through one of its bottom two holes

Ground already broken and rolled; you want 2 to 3 inches of loose crumb so the rake pulls stones and roots. Depth comes from your hands here: keep the handles light or lift a little. Pushing down digs deeper. Firm it again (walk or light roll) before the final rake and seed.

Tilled and rolled lawn bed under trees
The middle lawn at Tori and Bob's, tilled and rolled, Nov 21, 2026.

2. Weed a garden between rows

Tines
Forward
Silver drag
#1 down
Black depth
Raised, bottom holes

Only scratch 1 to 2 inches so you cut weeds without bringing up new weed seed. Walk a little faster and keep the handles up so the tines skim.

3. Break sod or ground never tilled

Tines
Reverse (counter-rotating)
Silver drag
Up to #2
Black depth
Start in the top Cultivate hole, step down to Till holes on later passes
  1. First pass shallow. The reverse tines bite hard and the tiller fights less if it is not buried.
  2. Second and third passes, move the depth pin down one hole each time.
  3. Rake out the sod clumps between passes.

4. Turn in compost or shredded leaves

Tines
Reverse
Silver drag
#2 up
Black depth
Upper Till holes, about 4 to 6 in

Spread the material first, then till across it in two directions so it mixes rather than layers.

5. Stony or root-filled ground

Tines
Forward
Silver drag
#1 down
Black depth
Raised

Go shallow and slow. If it bucks or jumps forward, ease off and pull stones by hand before the next pass. Stop the engine before clearing anything wrapped on the tines.

6. Moving it between jobs

Tines
Disengaged
Black depth
Transport hole, the top hole, so the tines ride clear

Wheels only across lawn, drive or pavement. Never run the tines on pavement.

If it misbehaves

What happensFix
Runs away or hops forward (forward tines)Check the silver drag stake is down at #1. Slow down.
Digs a hole and stalls (reverse tines)Move the black depth pin up one hole toward Cultivate.
Only scratches the surfaceReverse tines: move the depth pin down one hole. Forward tines: a little more weight on the handles.
Leaves big clodsSoil too wet. Wait a dry day, then a second pass.
SafetyRead the operator's manual. Stop the engine before unclogging tines or moving stakes. Keep people and kids clear. Take extra care backing up or pulling the tiller toward you.

Settings come from the decal on Ben's tiller and Husqvarna's drag stake rule (lower it for forward tines, raise it for reverse; TR317D manual, drag stake section). Depths are starting points; check your model's manual. Grow Together, Nov 2026.